|
|
|
Hub removable |
Post Reply 
|
| Author | |
pigeonguy 
Member 
Joined: 30 Sep. 2014 Location: Florida Status: Offline Points: 7 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Hub removablePosted: 01 Oct. 2014 at 9:40am |
|
How do I remove the hub/free wheel in/out part?
I have removed the bolts but when I pull on it something seems connected???? Don't want break it?
|
|
 |
|
|
athawk11
Member
Joined: 18 Jan. 2012 Location: Arvada,Colorado Status: Offline Points: 4151 |
Post Options
Thanks(0)
Quote Reply
Posted: 01 Oct. 2014 at 11:51am |
|
With the six bolts removed, it should slide off. It may have some gasket sealant holding it in place. Give it a few taps with a dead blow hammer.
Tim
|
|
|
1- 1946 CJ2A
2- 1949 CJ3A |
|
|
|
|
rocketeer
Member
Sponsor Member Joined: 26 June 2008 Location: Lehighton, PA Status: Offline Points: 3473 |
Post Options
Thanks(0)
Quote Reply
Posted: 01 Oct. 2014 at 9:26pm |
|
Depends. Is there a large nut or a clip on the outer end? If there is then the nut or clip has to be removed before the hub will slide off.
http://www.thecj2apage.com/forums/axle-shaft-types_topic3260.html Larry |
|
|
|
|
pigeonguy
Member
Joined: 30 Sep. 2014 Location: Florida Status: Offline Points: 7 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 Oct. 2014 at 9:12pm |
|
I will try to explain what I have.
The hub, with the long bolts, is loose but will not come off. I have even applied considerable force by wedging cold chisels and screw drives. It moves about 1/4" out. It will also turn 360 degrees? I am afraid to apply too much force. Also unable to use a puller. I am out of ideas. I also have tried removing it with the adjustment free and set on. GUY
|
|
|
|
|
pigeonguy
Member
Joined: 30 Sep. 2014 Location: Florida Status: Offline Points: 7 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 Oct. 2014 at 9:20pm |
|
Thanks for the replies. If I knew how I would post
a picture........\\GUY\ 1947 CJ2A I think>
|
|
|
|
|
1955cj5
Member
Joined: 21 Sep. 2012 Location: SW Idaho Status: Offline Points: 346 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 Oct. 2014 at 11:13pm |
|
Can you get the dust cap off? You may have to bolt the hub back on and tap the dust cover loose to see what is under there....a nut or a clip or?
|
|
|
|
|
pigeonguy
Member
Joined: 30 Sep. 2014 Location: Florida Status: Offline Points: 7 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 Oct. 2014 at 11:45pm |
|
I got it off. I did not realize that their was a dust cap!!!!!
Once I seperated the cap I could see the nut and shaft. Thanks for all the help Guys. |
|
|
|
|
Post Reply
|
|
| Tweet |
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options