|
|
|
Dana 44 Power-Lok |
Post Reply 
|
| Author | |
BD1 
Member 
Joined: 18 Dec. 2019 Location: Maine Status: Offline Points: 535 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Dana 44 Power-LokPosted: 23 Jan. 2023 at 7:42am |
|
I am looking for a Dana 44 30 spline Power-Lok for 3.73 gears
|
|
|
BD
'47 CJ2a, Shiny on top! '55 CJ5 project |
|
 |
|
|
oldtime
Member
Joined: 12 Sep. 2009 Location: Missouri Status: Offline Points: 3647 |
Post Options
Thanks(0)
Quote Reply
Posted: 23 Jan. 2023 at 8:39am |
|
The 30 spline units were used by IH and we’re also in some 1960’s Chevy pu’s.
Relatively few and far between. I built one of my Jeeps with a T18/D20 combo and so I used the 3.73 differentials for hiway cruising. I do know where you can get a set of 30 spline Powr Lok D44 side gears. I sold them a while back and the current owner is reselling them.
Edited by oldtime - 23 Jan. 2023 at 8:42am |
|
|
Currently building my final F-134 powered 3B .
T98-A Rock Crawler using exclusive factory parts and Approved Special Equipment from the Willys Motors era (1953-1963) Zero aftermarket parts |
|
|
|
|
BD1
Member
Joined: 18 Dec. 2019 Location: Maine Status: Offline Points: 535 |
Post Options
Thanks(0)
Quote Reply
Posted: 23 Jan. 2023 at 9:55am |
|
I would buy the 30 spline side gears if they will go in any Dana 44 Power-Lok. I have a centered flanged .373 Dana 44 I would like to use behind a dana 20 to avoid an overdrive. This would be in a '55 CJ5 with a 225. I'm looking for a little more drivability on the road in my next build.
|
|
|
BD
'47 CJ2a, Shiny on top! '55 CJ5 project |
|
|
|
|
oldtime
Member
Joined: 12 Sep. 2009 Location: Missouri Status: Offline Points: 3647 |
Post Options
Thanks(0)
Quote Reply
Posted: 23 Jan. 2023 at 10:28am |
|
Yeah that’s almost exact what I did to one of my flatties.
D225- WR T18- Terra low D20- center flanged D44 @ 3.73 - front and rear Powr Loks. I wanted it to be a relatively quiet jeep for long distance traveling yet still be a good off-roader. PM me for info on the side gears.
Edited by oldtime - 23 Jan. 2023 at 10:29am |
|
|
Currently building my final F-134 powered 3B .
T98-A Rock Crawler using exclusive factory parts and Approved Special Equipment from the Willys Motors era (1953-1963) Zero aftermarket parts |
|
|
|
|
BD1
Member
Joined: 18 Dec. 2019 Location: Maine Status: Offline Points: 535 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 Jan. 2023 at 6:12pm |
|
Unfortunately those sidegears were so led last week. Are you happy with the 225/3.73/lower transfer range setup?
|
|
|
BD
'47 CJ2a, Shiny on top! '55 CJ5 project |
|
|
|
|
oldtime
Member
Joined: 12 Sep. 2009 Location: Missouri Status: Offline Points: 3647 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 Jan. 2023 at 7:33pm |
|
The drivetrain is fully complete on that Jeep but I had to set the project aside for a full year now. Ready to start body work as soon as I finish the stainless exhaust,
I’m sure will absolutely love that particular drivetrain as a versatile combo hiway and trail jeep. My final build will be a tad more off-roadish. D225 / WR. T18 / Terra Low D18 / Warn OD / 4.89 offset flanged again with Powr Loks front and rear.
|
|
|
Currently building my final F-134 powered 3B .
T98-A Rock Crawler using exclusive factory parts and Approved Special Equipment from the Willys Motors era (1953-1963) Zero aftermarket parts |
|
|
|
|
geardaddy
Member
Joined: 01 Mar. 2014 Location: st.paul mn Status: Offline Points: 11 |
Post Options
Thanks(0)
Quote Reply
Posted: 25 Jan. 2023 at 8:45pm |
|
i have a 4.09 powr-lok. let me see if i have a 3.73 case to put the 30 spl guts in.....612-309-3999
|
|
|
|
|
Post Reply
|
|
| Tweet |
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options