oil filters |
Post Reply | Page 12> |
Author | ||
GaryArf
Member Sponsor Member Joined: 21 July 2005 Location: Baxter MN Status: Offline Points: 3905 |
Post Options
Thanks(0)
Posted: 19 Nov. 2006 at 8:15pm |
|
This one is a little confusing as I have four different types. I'm going to make some assumptions here as the parts lists are murky at best. Please give your input, as of this time I'm only speculating. In the '49 parts list it give A-1230 (up to Ser. No. 40352) This next one came on my '45 and was mounted on the fender as the Jeep had a plow on it. (notice the fender mounting bracket)
In the '49 parts list it gives Part # 645638 (purolator Products) (After Ser. No. 40352) This one was on my #58500. I didn't change it, so I'll (assume) it's original. I'll give the part # with all my "assumptions"
#643147 (after engine ser.# 40352) ( up to engine ser. #......) (yes this is like this in the parts book)
Finally I have this one. In the '49 parts list it has this at the end of all the other #'s.
(Fram F3-P2) (after engine Ser. No......) Yes that is what is in the book. I'm assuming here...This is on my neighbors Jeep with the MB motor.
As you can see each of these filter canisters are different in there size and mounting... even the straps are different, and after the straps were "scraped" the mounts to the bracket that hold it to the engine changed.
I am interested in what yours has and the ser. # your Jeep is.
Gary
|
||
CJ2A #10021 #34692 #58500
|
||
Lomar15
Member Sponsor Member Joined: 01 Jan. 2006 Location: Fanny Bay, B.C. Canada Status: Offline Points: 1226 |
Post Options
Thanks(0)
|
|
46 CJ2A #48777
42 MB Slat Grill 119898 Frame 51 M38 Body 42 MB #155950 Spen Trailer http://picasaweb.google.com/lomar15CJ2A |
||
sean
Moderator Group Sponsor Member Joined: 20 July 2005 Location: North Idaho Status: Offline Points: 7388 |
Post Options
Thanks(0)
|
|
Gary:
#16279 has the first one, A-1230, same as late MB, "Military Standard" Sean |
||
Howard
Member Sponsor Member Joined: 17 Feb. 2006 Location: New Mexico Status: Offline Points: 976 |
Post Options
Thanks(0)
|
|
Gary,
I am unclear on the difference between the top two. Can you please clarify what the lid says on the rim in the first photo. Also how about information on the drain plug location(s)? Thanks.
Howard
|
||
Howard F Jewett
1946 CJ2A #23353 43 GPW 106505 USA #20366014 43 Bantam Trailer T3 #14844 52 M100 K1119 |
||
Cammer
Member Joined: 26 Sep. 2006 Location: FL Status: Offline Points: 876 |
Post Options
Thanks(0)
|
|
Here's another one to add to the mix. I picked this one up a while back. It's an NOS canister but I'm not sure what it's for. What do you all think?
|
||
Cammer
Member Joined: 26 Sep. 2006 Location: FL Status: Offline Points: 876 |
Post Options
Thanks(0)
|
|
Here's the one that is currently on my jeep. Serial number 108844.
Edited by Cammer - 23 Dec. 2006 at 1:16pm |
||
vsprague
Member Joined: 15 May 2007 Status: Offline Points: 2 |
Post Options
Thanks(0)
|
|
any napa part number on a 1948 cj2a for the oil filter cartridge vsprague@cox.net
|
||
danthman
Member Joined: 22 Jan. 2008 Location: Yuma, AZ Status: Offline Points: 38 |
Post Options
Thanks(0)
|
|
and yet another... this is a 48
|
||
sean
Moderator Group Sponsor Member Joined: 20 July 2005 Location: North Idaho Status: Offline Points: 7388 |
Post Options
Thanks(0)
|
|
Looks correct for the vintage, but missing one clamping band.
|
||
Scott R
Member Joined: 16 Mar. 2007 Location: Gaines, MI Status: Offline Points: 1392 |
Post Options
Thanks(0)
|
|
The picture from danthman almost looks like it was taken from my jeep, right to the color of the jeep and the missing clamping band. Different air filter though.
Having just replaced the oil lines I wondered what the position of the canister should be? Before I took the canister off, the upper line was routed just like danthman's; going to the side of the bracket. Although for a couple reason I thought it made more sense to raise the canister and have the line run over the top, just like the last pic that Gary posted.
However to make that happen the canister needs to be fairly high and if I had the second clamping band it would be pretty darn low on the canister.
What is the intened position for my late 48 production?
|
||
Jerry 45
Member Joined: 01 Nov. 2006 Location: Cheshire, CT Status: Offline Points: 200 |
Post Options
Thanks(0)
|
|
Gary;
My 45 2A (#11802) has the first type of Filter. Jerry |
||
1945 CJ-2A 11802
1946 CJ-2A 19249 1948 VJ-2 Jeepster "They can have my Jeep when they can pry it from my cold, dead hands." |
||
sammy
Member Joined: 19 July 2007 Location: Albuquerque, NM Status: Offline Points: 504 |
Post Options
Thanks(0)
|
|
Fellows,
I will ad my filter to this list, it is a fram on an MB engine, no idea on identification Here are photos And after paint It is presumed by me to be the first filter shown, a Military filter as is stated on top, yet has a Fram label and is all black. |
||
sean
Moderator Group Sponsor Member Joined: 20 July 2005 Location: North Idaho Status: Offline Points: 7388 |
Post Options
Thanks(0)
|
|
Sammy
Sean |
||
sammy
Member Joined: 19 July 2007 Location: Albuquerque, NM Status: Offline Points: 504 |
Post Options
Thanks(0)
|
|
Good to know, and I'll just leave those pictures as an addition to the thread, mine CJ has an MB engine so it is correct I suppose :) Thanks! |
||
dwloop
Member Joined: 10 Feb. 2009 Location: St. louis, MO Status: Offline Points: 290 |
Post Options
Thanks(0)
|
|
So how do we know the difference between the Fram and the Purolator? And which one is the C3 and which is the C4 as listed on the parts sites when I attempt to purchase new flex lines?
Thanks,
Dave
|
||
CJ2A11425
Member Joined: 08 Aug. 2009 Location: Bow, Wa. Status: Offline Points: 11 |
Post Options
Thanks(0)
|
|
Jerry, I'm a recent owner of a 45 also, and am wanting to change the oil; I'm being told that there are a couple different filter sizes. Hoping that you can save me some of the leg work and let me know what filter works for you. Thanks, Tim
|
||
Tim
|
||
Jim Kilbourne
Member Sponsor Member Joined: 04 Mar. 2007 Location: Staunton, VA, USA Status: Offline Points: 233 |
Post Options
Thanks(0)
|
|
Can we get these photos, or new ones, posted up?
|
||
Jim Kilbourne
1945 Willys, CJ2A-10142 1946 Willys, CJ2A-26592(for sale) 1946 Willys, CJ2A-33725 projectrequest@motorhousellc.com http://motorhousellc.com |
||
mike in oregon
Member Sponsor Member Joined: 17 Jan. 2008 Location: Fall Creek Or Status: Offline Points: 1988 |
Post Options
Thanks(0)
|
|
Yes it would be great to be able to see these pictures now and in the future. all this info in the part section does no good if the picture go away after time. Is there anything we can do about this or am I the only one that cant see them? Thanks Mike
|
||
MIKE IN OREGON
President of Oregon Flat Fender Club. http://www.facebook.com/pages/Oregon-Flat-Fender-Club/222864787838570 46 CJ2A 38007 46 CJ2A 79863 BANTAM T3-C 25314 |
||
Post Reply | Page 12> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |