Forum Home Forum Home > CJ-2A Discussion Area > Modifications from original
  New Posts New Posts RSS Feed - Wheel Modifications
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Wheel Modifications

 Post Reply Post Reply Page  <1 234
Author
Message
WeeWilly View Drop Down
Member
Member
Avatar
Sponsor Member x 2

Joined: 07 May 2009
Location: Clayton IN
Status: Offline
Points: 3422
Post Options Post Options   Thanks (0) Thanks(0)   Quote WeeWilly Quote  Post ReplyReply Direct Link To This Post Posted: 11 Jan. 2018 at 4:54pm
I put a set of 600 X 16s on my 47 and have a couple thousand miles on them now and have had no trouble with them. The ones I received were 8 ply rating instead of the 6 ply that was in the add so mine is a little stiff. I would have liked to have 4 ply for these old bones but for the cost of them I am not going to complain, I don't even notice the logo on them.

   Jim
47 CJ2A (Ranch Hand) 48 CJ2A, 48 Willys truck, T3C 3782, M274 (Military Mule)
Back to Top
jpet View Drop Down
Moderator Group
Moderator Group
Avatar
Sponsor Member x 5

Joined: 30 Apr. 2008
Location: Ramsey, IL
Status: Offline
Points: 11173
Post Options Post Options   Thanks (0) Thanks(0)   Quote jpet Quote  Post ReplyReply Direct Link To This Post Posted: 11 Jan. 2018 at 5:04pm
Jim, would you say the rubber in the tread is softer?
CJ2A #29110 "General Willys"
MB #204827 "BAM BAM"

"We do what we can, and we try what we can't"
Back to Top
WeeWilly View Drop Down
Member
Member
Avatar
Sponsor Member x 2

Joined: 07 May 2009
Location: Clayton IN
Status: Offline
Points: 3422
Post Options Post Options   Thanks (0) Thanks(0)   Quote WeeWilly Quote  Post ReplyReply Direct Link To This Post Posted: 11 Jan. 2018 at 5:13pm
From a thumb nail test between the Speedway and a Goodyear that I have for a spare I would say the speedway is softer. Hope this helps a little and I enjoy watching you do the fine machine work Jeff.

   Jim
47 CJ2A (Ranch Hand) 48 CJ2A, 48 Willys truck, T3C 3782, M274 (Military Mule)
Back to Top
berettajeep View Drop Down
Member
Member
Avatar
Sponsor Member

Joined: 03 Feb. 2009
Location: Astoria OR
Status: Offline
Points: 4304
Post Options Post Options   Thanks (0) Thanks(0)   Quote berettajeep Quote  Post ReplyReply Direct Link To This Post Posted: 11 Jan. 2018 at 9:05pm
Originally posted by jpet jpet wrote:










This reminds me of Sarge from the Pixar movie Cars.
Back to Top
Ol' Unreliable View Drop Down
Member
Member
Avatar

Joined: 25 Sep. 2016
Location: CO Springs CO
Status: Offline
Points: 4226
Post Options Post Options   Thanks (0) Thanks(0)   Quote Ol' Unreliable Quote  Post ReplyReply Direct Link To This Post Posted: 12 Jan. 2018 at 2:12am
Tires that big do make Bam Bam look kinda... toylike.  I'd recommend you get an M-715 for the tires.  Smile
There's a reason it's called Ol' Unreliable
Back to Top
Bruce W View Drop Down
Member
Member
Avatar

Joined: 29 July 2005
Location: Northeast Colorado
Status: Offline
Points: 9611
Post Options Post Options   Thanks (0) Thanks(0)   Quote Bruce W Quote  Post ReplyReply Direct Link To This Post Posted: 12 Jan. 2018 at 6:44am
That was kinda my first impression, too.LOL  
  BW
It is NOT a Jeep Willys! It is a Willys jeep.

Happy Trails! Good-bye, Good Luck, and May the Good Lord Take a Likin' to You!

We Have Miles to Jeep, Before We Sleep.
Back to Top
jpet View Drop Down
Moderator Group
Moderator Group
Avatar
Sponsor Member x 5

Joined: 30 Apr. 2008
Location: Ramsey, IL
Status: Offline
Points: 11173
Post Options Post Options   Thanks (0) Thanks(0)   Quote jpet Quote  Post ReplyReply Direct Link To This Post Posted: 12 Jan. 2018 at 1:43pm
Bruce, I think you should move that rear axle back some. You will likely see better off-road performance with the longer wheelbase and better weight distribution. Front axle could go forward some too. HTH!

CJ2A #29110 "General Willys"
MB #204827 "BAM BAM"

"We do what we can, and we try what we can't"
Back to Top
oldtime View Drop Down
Member
Member
Avatar

Joined: 12 Sep. 2009
Location: Missouri
Status: Offline
Points: 4140
Post Options Post Options   Thanks (0) Thanks(0)   Quote oldtime Quote  Post ReplyReply Direct Link To This Post Posted: 12 Jan. 2018 at 4:56pm
Bruce, 
Do you wheel that on a regular basis ? Ha Ha Ha !

Hey Jeff...
I think you brought up a real good point the other day by showing us "too much tire" for the Jeep.
At some point these lightweight jeeps become truly disadvantaged by use of larger tires.
Whenever the tire gets too tall, too wide or too stiff the tread can no longer flex-form for full contact patch regardless of PSI.
7.50 x 16" at 32" diameter seems to be very near the limit for LRV size jeeps if you expect the tire to flex well at low PSI.
Obviously ply rating and compound density will effect the end results.

Concerning minimum PSI I expect pressures below 6 PSI will become problematic whenever tubes are installed. 
Any bead slippage will certainly destroy  tire tube at low PSI.

If I'm not mistaken your original quest was to control side roll at low PSI right ?
I believe that's referred  to as tire deflection.

Most all bias ply tires have a section width near 100% aspect ratio. 
So NDT's are all going to be very near to 100% aspect ratio.
Obviously a tire with lower aspect ratio should have less sidewall deflection.

It was determined years ago that the most practical section with is near the current 75% aspect ratio.
I believe that determination was about the time when the old school 78 series tires came to be.
Of course the original aspect ratio determinations were more about tire deflection during high speed cornering maneuvers.
Very few if any Jeeps are driven fast while cornering so we often opt for taller aspect ratios.
But still it holds true that a lower aspect ratio is key to preventing excess sidewall roll/ deflection at low tire PSI.
I would guess having the correct rim width to be a secondary concern toward preventing excess deflection.

So I don't think you'll get totally away from tire roll unless you somehow opt for tires having a lower aspect ratio.


Currently building my final F-134 powered 3B .
T98-A Rock Crawler using exclusive factory parts and Approved Special Equipment from the Willys Motors era (1953-1963)
Zero aftermarket parts

Back to Top
jpet View Drop Down
Moderator Group
Moderator Group
Avatar
Sponsor Member x 5

Joined: 30 Apr. 2008
Location: Ramsey, IL
Status: Offline
Points: 11173
Post Options Post Options   Thanks (0) Thanks(0)   Quote jpet Quote  Post ReplyReply Direct Link To This Post Posted: 12 Jan. 2018 at 5:33pm
Again, I have no plans to start running 900-16 NDTs. I just put these tires on to show myself and some others what 35" NDTs would look like. I also wanted some photos of it for another purpose. I will run 750-16 NDTS.

My 750-16 NDTs have a 6.2 wide tread and the recommended wheel width is 5.5' - 6.5' wide, i.e. 6". I'm not a tire expert, but it only makes sense that a 6" wide wheel/tire would have less side flex than a 5" wide wheel/tire simply by better weight displacement. Yes, lowering your aspect ratio would be more significant, but I still need ground clearance which is more important. I want to run the maximum tire diameter I can that still looks stock. That would be 750-16 NDT and 6" is the better wheel width.

We can crunch numbers to a point but I prefer the method of wheeling the tires and wheels to see what happens and make adjustments based on that.

Lee and I have had the conversation on whether or not 900-16 NDTs kick you out of the "Super Stock" class. My general rule of thumb applies to not only the tires but the entire jeep. If people ask you, "Is it stock?", you are still in the club. When they stop asking you, "What year is it?",... you have really crossed the line
CJ2A #29110 "General Willys"
MB #204827 "BAM BAM"

"We do what we can, and we try what we can't"
Back to Top
 Post Reply Post Reply Page  <1 234

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.06
Copyright ©2001-2022 Web Wiz Ltd.