Joe DeYoung's Tools and Parts Listing |
Post Reply | Page <1234> |
Author | ||
19Cargo42
Member Joined: 23 Apr. 2018 Location: Western Mass. Status: Offline Points: 565 |
Post Options
Thanks(0)
|
|
Joe, thumbnail photos that people could click to expand could work. If you want, I can PM you my email address and you can send them to me and I’ll post them for you.
John
|
||
Joe DeYoung
Member Sponsor Member x 2 Joined: 20 July 2005 Location: Madison WI Status: Offline Points: 3354 |
Post Options
Thanks(0)
|
|
I'm up to my eyeballs in shop work so no time for that now, but I may take you up on that in the near future when I get a chance to take pics. Thanks for the offer.
|
||
Joe DeYoung
to many jeeps, parts, and accessories to list here, but apparently enough to keep me in trouble with my wife. |
||
19Cargo42
Member Joined: 23 Apr. 2018 Location: Western Mass. Status: Offline Points: 565 |
Post Options
Thanks(0)
|
|
I'm at your disposal when it's convenient.
John
|
||
jeepman1950
Member Joined: 08 Mar. 2021 Location: New York Status: Offline Points: 2 |
Post Options
Thanks(0)
|
|
Good Morning Joe, i would like to order # 28 tranfir case seal puller $28.00....
My e mail is williamwts1950@charter. Thank you, Bill Smith
|
||
WTS
|
||
jeepman1950
Member Joined: 08 Mar. 2021 Location: New York Status: Offline Points: 2 |
Post Options
Thanks(0)
|
|
Good morning Joe, I would like to order # 28 t case seal puller
my e mail is: williamwts1950@charter.net so i can place an order with you.... |
||
WTS
|
||
Spinnas
Member Joined: 24 Apr. 2018 Location: AZ Status: Offline Points: 375 |
Post Options
Thanks(0)
|
|
Message sent
|
||
BD1
Member Joined: 18 Dec. 2019 Location: Maine Status: Offline Points: 626 |
Post Options
Thanks(0)
|
|
Here's a free plug for Joe's pinion/transfer case output seal puller. Most of these seals That I've pulled have been on the bench, (or horses) with the pinion or output shaft removed. The normal Napa seal puller I've used for years works just fine for that. However, on the the jeep, with the shaft splines in the way, not so easy. Until now. No regrets for the cost of this tool!
Edited by BD1 - 20 July 2021 at 7:12pm |
||
BD
'47 CJ2a, Shiny on top! '55 CJ5 project |
||
mike in oregon
Member Sponsor Member Joined: 17 Jan. 2008 Location: Fall Creek Or Status: Offline Points: 1988 |
Post Options
Thanks(1)
|
|
Is that # 28 on his list? I might have to get one
|
||
MIKE IN OREGON
President of Oregon Flat Fender Club. http://www.facebook.com/pages/Oregon-Flat-Fender-Club/222864787838570 46 CJ2A 38007 46 CJ2A 79863 BANTAM T3-C 25314 |
||
Joe DeYoung
Member Sponsor Member x 2 Joined: 20 July 2005 Location: Madison WI Status: Offline Points: 3354 |
Post Options
Thanks(0)
|
|
Yes, that is #28.
|
||
Joe DeYoung
to many jeeps, parts, and accessories to list here, but apparently enough to keep me in trouble with my wife. |
||
Joe DeYoung
Member Sponsor Member x 2 Joined: 20 July 2005 Location: Madison WI Status: Offline Points: 3354 |
Post Options
Thanks(0)
|
|
Out of my own personal necessity I have a new tool to offer... A distributor Wrench for those frozen distributors that just wont budge. It safely clamps onto the lower portion of a distributor with a outside diameter of 3.125 . The long handle gives you something safe to tap on to rotate the distributor. I've added it to the bottom of the list on the 1st post in this thread. Hope it helps people out. I also can make theses for the smaller diameter distributors as well... just haven't personally need one or had a request for one. The small hole version would work just the same.
Edited by Joe DeYoung - 16 Sep. 2021 at 5:42pm |
||
Joe DeYoung
to many jeeps, parts, and accessories to list here, but apparently enough to keep me in trouble with my wife. |
||
3-48s
Member Joined: 18 Sep. 2008 Location: Upstate, NY Status: Offline Points: 2780 |
Post Options
Thanks(0)
|
|
Hey Joe, How fortuitous! I am in need of this exact tool for two of my 2As. You are the "Go Devil Man" for sure. Please sign me up for one ASAP! Greg |
||
1945 CJ2A #10536
1948 CJ2A #176528 "Elmer" 1948 CJ2A #155970 "Gray Mule" 1948 CJ2A #155365 "Old Yeller" (GONE) BANTAM T3C # 6147 (GONE) BANTAM T3C # 30856 |
||
rocnroll
Member Sponsor Member Joined: 20 July 2005 Location: Tuscumbia, AL Status: Offline Points: 13563 |
Post Options
Thanks(0)
|
|
Another good one !!
|
||
'47 CJ2A PU
'48 CJ2A Lefty "Common sense is not that common" |
||
Ron D
Member Joined: 27 Oct. 2019 Location: South Carolina Status: Offline Points: 1403 |
Post Options
Thanks(0)
|
|
Hi Joe, I'm interested, can you please post or send me a photo of your #4 Cam Gear Puller? Thanks!
|
||
1951 M38
1951 M100 |
||
drm101
Member Joined: 12 Dec. 2012 Location: Clarkston, MI Status: Offline Points: 1468 |
Post Options
Thanks(0)
|
|
Joe the Go To Go Devil Man! That does look handy.
|
||
Dean
'47 CJ2A "Mud Hen" The less the Power the More the Force |
||
erik.mitchell@cellul
Member Joined: 09 Oct. 2021 Location: Richmond VA Status: Offline Points: 1 |
Post Options
Thanks(0)
|
|
Hey Joe… I need to yolk puller and your version of the Miller W Dash 251… How do we make that happen? Your tools look great
|
||
jeep fitter
Member Joined: 02 June 2010 Location: Macungie, Pa Status: Offline Points: 27 |
Post Options
Thanks(0)
|
|
Hey Joe ,
(29) puller ,shift rail transfer case. If you have this in stock it would make my day. I’m replacing seals on transfer case .
|
||
Joe DeYoung
Member Sponsor Member x 2 Joined: 20 July 2005 Location: Madison WI Status: Offline Points: 3354 |
Post Options
Thanks(0)
|
|
Yes, I stock them. PM sent
|
||
Joe DeYoung
to many jeeps, parts, and accessories to list here, but apparently enough to keep me in trouble with my wife. |
||
Oldowl
Member Joined: 15 Mar. 2019 Location: San Angelo, Tx Status: Offline Points: 6 |
Post Options
Thanks(0)
|
|
Would like to purchase #28 & #29 seal pullers let me know how you want payment! Thanks Oldowl
|
||
Post Reply | Page <1234> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |