How to carry String Trimmers and Pole Saws? |
Post Reply | Page 12> |
Author | |
JeepFever
Member Sponsor Member Joined: 07 Aug. 2012 Location: VA Status: Offline Points: 2735 |
Post Options
Thanks(0)
Posted: 16 Mar. 2022 at 9:12pm |
My son acquired some land a couple years ago that requires a lot of trail maintenance. Wilson is a working '2A and called into service for this task. I am trying to come up with a way to carry some of the longer tools required. Looking for ideas . . . if anyone has been doing this for years. No sense "reinventing the wheel" :-) Until now, I have been setting the "base" in the rear, and put the shaft on front seat (or thru the windshield in case of pole saw). Several "cons" to this, biggest of which -> I can carry no passengers.
I was first thinking of somehow mounting something similar to a "gun rack" on the side, like seen on lawn contractor trailers. It has to be easily removable, and no new holes in original tub etc. Also, some of trails are tight, so can not stick out too far. This is my prototype of a pole saw holder. I actually really like this. Weight is supported in back, the shaft is resting on a bracket attached to windshield frame, in foam, so has lots of give for windshield movement. The shaft is high enough that a passenger can squeeze in. That is a 5/16" rod with (2) 90deg bends. (currently duct taped to windshield). If I only needed to carry this battery pole saw, I would be done. I could refine this prototype . . BUT . . I would also like to carry a fairly large gas string trimmer at same time. edit: just noticed that Wilson's Rubicon damage is very visible in this light. Edited by JeepFever - 16 Mar. 2022 at 9:36pm |
|
Scratch
Member Joined: 30 July 2019 Location: Hudson, WI Status: Offline Points: 1440 |
Post Options
Thanks(0)
|
Interested to see any good ideas. I'm always looking for a better way to carry my brush cutter. I now use my ATV with those Koplin rubber coated gun racks.
|
|
43 GPW 93487 Blk
44 GPW 230283 OD 46 CJ2A 50100 Tan 46 CJ2A 77632 Wht 47 CJ2A 141681 Grn 48 CJ2A 156240 Red/Yel 48 CJ2A "Lefty" 181341 Red 61 CJ5 123120 Tan 03 TJ Inca Gld |
|
Greyghost
Member Joined: 26 June 2021 Location: VIC Australia Status: Offline Points: 19 |
Post Options
Thanks(0)
|
for long things I use a length of poly drain pipe tied to the roof rack/cage
somethings allow me to run a cap on each end or just the one. if something sticks out, its usually held in place with a bungee cord, for fast access
|
|
cpt logger
Member Joined: 23 Sep. 2012 Location: Western Colorad Status: Online Points: 3022 |
Post Options
Thanks(0)
|
If the trailer is always with you, build or modify a "ladder rack" for it. Make it low enough that you can easily reach the tools. This way you can carry passengers and also haul wood or dirt. Using my "Bubba voice"; Heck, unless it "needs" to be pretty, the rack does not even need to be made out of metal. Wood works well & is more flexible than steel. A few minutes using small trees or branches, some baling twine or wire, and a chain saw will get er done.
|
|
Rus Curtis
Member Joined: 25 Mar. 2010 Location: Alabama Status: Online Points: 1733 |
Post Options
Thanks(0)
|
The first thing I thought of was using the stock top bow sockets. Same concept you floated about how lawn care racks are made. Would need to carefully place the tools to keep from interfering with trailer when cornering - and an offset to clear the rollbar/windshield frame. Too many tools could eventually set up too much stress on the sockets though.
I think the same thing could be set up in the trailer with a frame sitting in the bed and extending up - would need to keep the back end open to load/unload that mower (or have a quick removal brace to help support when driving around). I like the idea of wood or PVC but metal could prove better (especially if eyeballing the stock bow sockets).
|
|
Rus Curtis
Alabama 1954 CJ3B Bantam T3-C |
|
JeepFever
Member Sponsor Member Joined: 07 Aug. 2012 Location: VA Status: Offline Points: 2735 |
Post Options
Thanks(0)
|
Thanks guys for the ideas, I literally thought about each one. (even a chainsaw created log solution)
In my opening post, I show the pole saw with a "hook bracket" on the windshield frame, and really liked the simplicity. Then I also found out that my string trimmer would set on quarter panel, shaft running outside of rollbar, and the string end in the same bracket as the pole saw. Nice fit. I was thrilled . . this turned out so easy!! It was very secure. Unfortunately, it only seemed great in the driveway, and on some wide trails. Today I was navigating a narrow trail, and was constantly watching to make sure I did not hook the pole saw on a hanging branch. I would really stink to hook something and bend the shaft. Back to the drawing board. I mounted the tire/gas rack, in case that gave me some new mounting options, (no new holes in tub) but that did not really give me any other ideas. Then, I found a folding-table frame in my steel scrap pile, 1" tubing, perfect fit for top bow bracket mount. This is what I came up with so far: What I like about this: - the cutting end of pole saw is further back and lower (plus, if turned upside-down, the chain bar is less likely to hang something) - the string trimmer is better protected, compared to hanging outside the rollbar. even inside it is not too difficult to load/unload (this position only works because I removed the string guard a long time ago, don't like them, plus I rarely use a blade) - this table-frame gives possible options for mounting other tools on it and/or rollbar Amazing how well that table frame fits. The table end (top) fits nicely in the top bow bracket, and the "leg" (bottom) rests nice on the tire frame. (also rests nicely on tailgate, but I do not want to drill any holes in that. I need to mount the tire, to check for clearance issues. I might want to mount tire and all tools at some point. Edit: one downside, the string trimmer shaft is lower than before. However, I was still able into get into passenger seat with some contortions. I am sure the grandkids will have no issues.
Edited by JeepFever - 14 June 2022 at 11:45pm |
|
JeepFever
Member Sponsor Member Joined: 07 Aug. 2012 Location: VA Status: Offline Points: 2735 |
Post Options
Thanks(0)
|
Hmmm . . as mentioned above, I just noticed this might cause some clearance issues with mower handle in a right-hand turn. I don't always have the trailer attached, but often enough that it is a concern.
I have always loaded the mower backwards for heavier tongue weight, Maybe the weight distribution would be fine if loaded front first. It would be easier to load that way . . going backwards is a pain.
|
|
cpt logger
Member Joined: 23 Sep. 2012 Location: Western Colorad Status: Online Points: 3022 |
Post Options
Thanks(0)
|
Nice! KISS. I love these simple fixes using recycled material. I especially like that you had it all on hand. |
|
Scratch
Member Joined: 30 July 2019 Location: Hudson, WI Status: Offline Points: 1440 |
Post Options
Thanks(0)
|
I don't like the idea of anything hanging out the side for tight trails. What about taking something like maybe your table frame legs, or something longer... Something that might look like a 3 foot wide, 5 foot long ladder, and setting that in the back. Like butted up to the back of the front seats, and resting on the top edge of the tailgate so the whole thing will be at an angle going back and up, then setting or strapping the saw and trimmer to that. It could even be easily made from scrap lumber.
The downward angle should keep them inside pretty well, easy to access from either side, easily secured for when you get a little wild, nothing hanging out the sides of the jeep, still able to tow your trailer. Maybe even mounting some U shaped mounts like the Koplin gun racks or just some pegs or something. Just another idea to throw out there.
Edited by Scratch - 19 Mar. 2022 at 9:07am |
|
43 GPW 93487 Blk
44 GPW 230283 OD 46 CJ2A 50100 Tan 46 CJ2A 77632 Wht 47 CJ2A 141681 Grn 48 CJ2A 156240 Red/Yel 48 CJ2A "Lefty" 181341 Red 61 CJ5 123120 Tan 03 TJ Inca Gld |
|
JeepFever
Member Sponsor Member Joined: 07 Aug. 2012 Location: VA Status: Offline Points: 2735 |
Post Options
Thanks(0)
|
I agree that I don't like anything hanging out the side. Nothing in this current design extends out past the quarter panel or fenders. Granted, in an off-camber situation, the tools would be outside a vertical plane from Jeep body. ie. if close to taking out the windshield, or crashing rollbar into tree, the tools would be in danger.
I was blazing new trail today, and it is as tight and off-camber as any I plan to carry tools on. No scary moments at all (the original design was scary on same trails). I am probably going to proceed with this. If I understand your suggestion, it might restrict access to the "bed" of Jeep. That would be an issue, because I store lots of other things there, and need easy access. (chainsaws, tow straps, snatch blocks, gas, oil, face shield, etc. Edited by JeepFever - 14 June 2022 at 11:48pm |
|
JeepFever
Member Sponsor Member Joined: 07 Aug. 2012 Location: VA Status: Offline Points: 2735 |
Post Options
Thanks(0)
|
Design as used today. Not really obvious in photo, and as mentioned above, nothing extends outside a vertical plane extended up from quarter-panel and fenders (and the pole saw is no higher than windshield, easy to keep an eye on, if things got tight) . I was much happier with it in the trails today. If anyone noticed the bag, I discovered another con of the design (in addition to mower handle clearance), the polesaw could be an head knocker. I never hit my head, but came close twice. I plan to keep the bag on board. :-) Another view of bag, but also to show the temporary mount to tailgate. I made a wooden block to keep the table frame centered, then pull down with bungee cord. I no longer need the spare tire carrier, so removed it. I plan to eventually narrow that table frame, but want to use it more first, in case I think of something else I might want to mount to it. Edited by JeepFever - 19 Mar. 2022 at 8:37pm |
|
JeepFever
Member Sponsor Member Joined: 07 Aug. 2012 Location: VA Status: Offline Points: 2735 |
Post Options
Thanks(0)
|
It is sometimes handy to use the tailgate as a work bench. I assumed that I would have to take the "table frame" off. To my surprise though, I could leave in on the Jeep by just rotating it on the bow bracket . . a swing-away mount. haha
Edited by JeepFever - 14 June 2022 at 11:54pm |
|
bight
Member Sponsor Member x 2 Joined: 20 Aug. 2020 Location: mid coast maine Status: Online Points: 1641 |
Post Options
Thanks(0)
|
i have been contemplating this topic for a long time and not come up with a workable solution. long brush cutters do not do well sideways in the back of the Jeep.
these cable clamps do work well to go around the windshield and the aftermarket top bow (80's vintage BesTop bow). i did add bike tire innertube for the smaller diameter bow tubing. there is no interference to opening the windshield, no drilling any holes, no welding or gluing needed. https://www.amazon.com/gp/product/B00NV8OPFO/ref=ppx_yo_dt_b_asin_title_o05_s01?ie=UTF8&psc=1 these (below) are the Bigg Lugg tool holders themselves that i am going to try out. they work great on a pants/tool belt. not certain they will be great for this application. they need to be cut off as shown to reduce the springy nature. i will also velcro strap the tool in just to ensure no "bounce out". the test hook i used was an old one i had that the ball fell off. i ordered new ones for the final application. https://www.amazon.com/gp/product/B01N94BVTY/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 cut down version: this is too springy: the cut off piece: will get out with the "prototypes" in a bit and report back. Edited by bight - 18 May 2022 at 7:58pm |
|
CJ-2A 72586 tan (stock)
CJ-2A 197624 green (resto-mod) the wife abides (def: to bear patiently; TOLERATE) |
|
bight
Member Sponsor Member x 2 Joined: 20 Aug. 2020 Location: mid coast maine Status: Online Points: 1641 |
Post Options
Thanks(0)
|
back with some progress. this system is working fine. made it out and back over very rough terrain without losing the brush cutter. now i just need another brush cutter, front mounts with controls and speed racer attacks the dastardly pricker brush!
while that idea cooks, here is the progress. i will post again when i receive and mount gen 2. the hooks also swing back out of the way when not in use. |
|
CJ-2A 72586 tan (stock)
CJ-2A 197624 green (resto-mod) the wife abides (def: to bear patiently; TOLERATE) |
|
Greyghost
Member Joined: 26 June 2021 Location: VIC Australia Status: Offline Points: 19 |
Post Options
Thanks(0)
|
thats a nice clean and non-destructive solution
|
|
bight
Member Sponsor Member x 2 Joined: 20 Aug. 2020 Location: mid coast maine Status: Online Points: 1641 |
Post Options
Thanks(0)
|
got the final versions installed and you could easily put on another set to stack tools:
and they flip back out of way when not being used: Edited by bight - 22 May 2022 at 8:23pm |
|
CJ-2A 72586 tan (stock)
CJ-2A 197624 green (resto-mod) the wife abides (def: to bear patiently; TOLERATE) |
|
windyhill
Member Joined: 14 Mar. 2009 Location: North East PA Status: Offline Points: 1395 |
Post Options
Thanks(0)
|
open the windshield all the way and run them through so they don't hang out. should be about to add a simple rest with piece of rubber hose or pool noodle etc.
|
|
'48 CJ2A
'53 CJ3B '59 CJ6 '65 CJ5 '67 CJ5 |
|
tamnalan
Member Joined: 08 Oct. 2013 Location: Port Orford, OR Status: Offline Points: 986 |
Post Options
Thanks(0)
|
Not a string trimmer, but here's another solution
|
|
Alan Johnson
1942 MB - "TBD" 1943 MB - "Lt Bob" 1950 cj3a M-100 x2 teardrop camper: https://forums.g503.com/viewtopic.php?f=141&t=201740 |
|
Post Reply | Page 12> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |