Replacing bed idea |
Post Reply |
Author | |
mickeykelley
Member Joined: 26 May 2016 Location: Republic of Texas Status: Offline Points: 440 |
Post Options
Thanks(0)
Posted: 14 Mar. 2017 at 6:17pm |
My bed, like most was rusted through in a number of places and of course wavy. At some point someone added a flat steel floor over the top of the existing wavy, hole filled factory. It was made with a 1.5-2 inch lip and was actually just set inside and the bolted to the side walls every 3 inches or so and finally caulked the top edge in an effort to prevent moisture getting between the original floor and this new flat piece. That piece is clearly strong enough as it had no dents, waves, etc and I found evidence it was used to haul gravel, including converting the tail gate to a dump style with the bottom opening like a dump truck.
Now, I would like to preserve the look of the original with one of those MDJuan replacement beds, but don't want to end up with inevitible waves. I know I could add more support underneath to the frame,but I can see still getting depressions due to the thin MDJuan metal. My thought was to cut out the old bed and weld in the flat piece that the PO used. Then weld on top of it the MDJuan bed. Good strength and look of original. However, I'm concerned about trapping moisture between the two. I know I could always paint before putting together, but the welding will burn off paint in places, thus leaving some vulnerable spots. Give me your input on the idea as well as suggestions for sealing the inner part of sandwich. |
|
WeeWilly
Member Sponsor Member x 2 Joined: 07 May 2009 Location: Clayton IN Status: Offline Points: 3422 |
Post Options
Thanks(0)
|
You could just use a piece of 1/2" plywood placed on the bottom of your trailer when using it to prevent damage, that I my intensions when I finish mine.
Jim |
|
47 CJ2A (Ranch Hand) 48 CJ2A, 48 Willys truck, T3C 3782, M274 (Military Mule)
|
|
JeepFever
Member Sponsor Member Joined: 07 Aug. 2012 Location: VA Status: Offline Points: 2735 |
Post Options
Thanks(0)
|
Interesting idea to use thicker steel under thin bed. Unfortunately, I have no ideas on how to "seal" between the layers.
Similar to WeeWilly, I chose to put something on top of the bed, when loading damaging materials. . . . My choice though, was a rubber mat from local farm supply. (I think designed for horse stalls, etc). It is 1/2" thick or more, and works great. . . Pull it out when you want to see the floor. :-)
|
|
63owner
Member Joined: 09 Jan. 2011 Location: Owensboro, Ky. Status: Offline Points: 472 |
Post Options
Thanks(0)
|
I saved a truck bed mat that I kept when I sold my Ford ranger pickup a couple of years ago. I cut it down to fit nicely in the bed of my Spen.
|
|
1948 CJ2A
1963 CJ3B Late 1940s(?) Spen trailer |
|
Hey2a
Member Joined: 27 Apr. 2012 Location: Dover DE Status: Offline Points: 293 |
Post Options
Thanks(0)
|
The bed area is such a small area...Unless the MD Juan is paper thin...using square stock to re enforce the frame underneath should work well...and not trap too much water
|
|
1946 CJ2a
1978 CJ7 2002 KJ M100 |
|
mickeykelley
Member Joined: 26 May 2016 Location: Republic of Texas Status: Offline Points: 440 |
Post Options
Thanks(0)
|
I got a reply from them saying they use 18 ga.
|
|
Post Reply | |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |