Stan’s Instagram vids |
Post Reply | Page <1 23456 9> |
Author | |
smfulle
Member Sponsor Member Joined: 16 Sep. 2010 Location: Ogden, Utah Status: Offline Points: 6141 |
Post Options
Thanks(0)
|
If everybody leaves and you’re still moving you win by default.
|
|
smfulle
Member Sponsor Member Joined: 16 Sep. 2010 Location: Ogden, Utah Status: Offline Points: 6141 |
Post Options
Thanks(0)
|
Here we are charging up the final climb to the summit if Imogene Pass. At just over 13,100 ft I think it’s the highest we’ve ever been. I’m m looking kinda pumped to get to the top because I spent the last half hour at the switchback just out of sight with the hood up, pouring water on the fuel pump and waiting for things to cool off and cure the vapor lock that was plaguing me from the Tom Boy ruins to there.
Rick G gives me the “Go Devil Power” cheer because he was having the same trouble and we were the only jeeps on this trip still powered by original L134s. |
|
Stev
Member Sponsor Member Joined: 27 July 2016 Location: Cincinnati Status: Offline Points: 2391 |
Post Options
Thanks(0)
|
Imogene Pass!
Tell us more about your L134 performance issues on this climb. You mentioned vapor lock, what was your engine temp on the gauge? Did you advance the timing for altitude? Possible things that could be done to address the vapor lock: We could come up with a heat shield for the fuel pump and fuel lines on the L134. There is also a heat shield for the carburetor that is on the L134s used in stationary applications like the welders and generators had. There is not a lot of air flow that gets to the fuel pump behind the engine front plate. One options is to install a 6 bladed fan on the L134. In the old days they did that on heavy trucks that sometimes had to run parked for hours, running radios in the military or fire services applications. They also installed an engine oil cooler to pull heat out of the oil (I have not seen a oil cooler for a L134). Edit - found a 6 blade fan link
Edited by Stev - 16 Sep. 2020 at 4:04pm |
|
Stev
1946 CJ2A Trail Jeep (The Saint), 1948 CJ2A Lefty Restored |
|
smfulle
Member Sponsor Member Joined: 16 Sep. 2010 Location: Ogden, Utah Status: Offline Points: 6141 |
Post Options
Thanks(0)
|
I've done nothing really to mitigate the vapor lock issues. This was my 3rd time over Imogene but the 1st time I ever had any vapor lock issues. Here's some conditions that probably contributed. 1. This was one of the hottest days in July. You can see in the video that I am in short sleeves. This is pretty unusual at that high altitude. The previous two trips had much cooler weather. One was even in a rainstorm with fog. 2. We were trying to rush through the trail a little bit because some of us were heading out that evening to drive to Moab. Fewer rest/cooling off stops and higher revs in order to travel faster. Engine temps were getting up to the 210 area at times. 3. On previous trips we have stopped at the Tom Boy mine/town ruins just before the final assent to rest and look around at the interesting remains. This time we rolled on through without giving the jeeps a chance to rest and cool. I'm headed off to the Fall Color Tour this next week and have not done any mitigation. We will see if the Sept vs July temps make a difference in performance at high altitude. I suspect it will. I may look into some heat wrap for the fuel lines. i have never had any trouble with this until this year. I guess my magic is wearing off. |
|
smfulle
Member Sponsor Member Joined: 16 Sep. 2010 Location: Ogden, Utah Status: Offline Points: 6141 |
Post Options
Thanks(0)
|
Here’s a couple from Colorado’s Carnage Canyon. “38 inch tires recommended.”
|
|
smfulle
Member Sponsor Member Joined: 16 Sep. 2010 Location: Ogden, Utah Status: Offline Points: 6141 |
Post Options
Thanks(0)
|
Here’s Bob Westerman (Bob W) and X-98 winching and climbing out the exit of Carnage Canyon.
|
|
smfulle
Member Sponsor Member Joined: 16 Sep. 2010 Location: Ogden, Utah Status: Offline Points: 6141 |
Post Options
Thanks(0)
|
Bumping and scraping in Carnage Canyon.
|
|
smfulle
Member Sponsor Member Joined: 16 Sep. 2010 Location: Ogden, Utah Status: Offline Points: 6141 |
Post Options
Thanks(0)
|
Here’s a fun one. Coming down a steep walk and blew a tire off the bead in spectacular fashion.
|
|
drm101
Member Joined: 12 Dec. 2012 Location: Clarkston, MI Status: Offline Points: 1470 |
Post Options
Thanks(0)
|
Are you running tubes?
|
|
Dean
'47 CJ2A "Ron" '66 CJ5 "Buckie" The less the Power the More the Force |
|
smfulle
Member Sponsor Member Joined: 16 Sep. 2010 Location: Ogden, Utah Status: Offline Points: 6141 |
Post Options
Thanks(0)
|
I've been running tubes forever until the last few months. I have pinch quite a few tubes while running at 9 psi or so on the trail. Fold over a tire, pinch a tube, flat tire. Recently I have been conducting an experiment with tubeless. As a couple of my tubes have gotten pinched and leaked I have pulled the tubes and put a valve stem in to run them tubeless. At the same time I have added a cup or so of laundry starch to the tire to help seal up in small leaks at the bead or in the tread. I have not done anything else to my stock style wheels to run them tubeless. No gorilla tape, no safety bump welds, nothing. So when the bead popping incident happened in the above video, I was running tubeless on both passenger tires and tubes on both drivers tires. The tire that blew was tubeless. I believe that had a tire with a tube and 9 psi been put under the stress that I put the blown tire under, I would have pinched a tube, had a flat and been required to use the spare, then repair the leaky tube at a later time. In this incident, I jacked up the jeep to get weight off the tire, wrapped a ratchet strap around the tire to reseat the bead, then pumped the tire up with a small portable compressor. In all it took about 10 minutes, did not require using the spare and did not require breaking down the tire to get the tube out and patch it. This was the first issue I have had with the tubeless tires. I ran them at the Fall Color Tour, including trips up Pearl Pass and Carnage Canyon without issue. I am pretty sold on the tubeless concept and as the tubes fail in my other tires, they will be pulled out. |
|
Stev
Member Sponsor Member Joined: 27 July 2016 Location: Cincinnati Status: Offline Points: 2391 |
Post Options
Thanks(0)
|
Another amazing Video! Running 9 PSI Tubeless with laundry starch - That is actually amazing. Is laundry starch a old time tire mounting trick or is this something new? Do people doing this keep a jug of laundry starch in their Jeeps in case they need to remount a tire or is one application sufficient for remounting on the trail?
|
|
Stev
1946 CJ2A Trail Jeep (The Saint), 1948 CJ2A Lefty Restored |
|
smfulle
Member Sponsor Member Joined: 16 Sep. 2010 Location: Ogden, Utah Status: Offline Points: 6141 |
Post Options
Thanks(0)
|
Old time trick? Probably, but I learned about recently from Jpet. I don’t carry a jug of the stuff in my Jeep, but I think Jeff does. I carry some in my Jeep support F150 and I have a Harbor Freight tire machine bolted to my trailer for easy tire busting. In this instance I just reseated the bead and inflated. Ran the rest of that day and the next without incident. It’s still holding air as it sits in the garage.
|
|
smfulle
Member Sponsor Member Joined: 16 Sep. 2010 Location: Ogden, Utah Status: Offline Points: 6141 |
Post Options
Thanks(0)
|
Here’s the climb up Hamburger Hill that we did before coming down and blowing a tire.
|
|
smfulle
Member Sponsor Member Joined: 16 Sep. 2010 Location: Ogden, Utah Status: Offline Points: 6141 |
Post Options
Thanks(0)
|
Another climb up the Escalator. I've posted climbs on this obstacle several times. hope it's not getting boring.
|
|
smfulle
Member Sponsor Member Joined: 16 Sep. 2010 Location: Ogden, Utah Status: Offline Points: 6141 |
Post Options
Thanks(0)
|
The first real obstacle on the Kane Creek trail in Moab.
|
|
otto
Member Joined: 26 Feb. 2012 Location: Orygun Status: Offline Points: 2265 |
Post Options
Thanks(0)
|
Nope, not boring!
|
|
47 CJ2A w/fuel injected boat engine
48 CJ2A 64 Ford Econoline Travelwagon If you can't get there in a Jeep, get a motorcycle! |
|
drm101
Member Joined: 12 Dec. 2012 Location: Clarkston, MI Status: Offline Points: 1470 |
Post Options
Thanks(0)
|
Thanks for the tire info Stan. All these little bits of knowledge on this page are what set it apart. I think there's a big difference between where you are and here in Michigan, but it's important to know if I plan to travel there. Here it's all sand and gravel, unless I go to the UP. We almost need a how to document for each area of the country. Sand dunes, gravel, snow, slick rock, etc.. On new cars, you just turn the knob to that setting. With an old Willys it's a bit more complicated.
|
|
Dean
'47 CJ2A "Ron" '66 CJ5 "Buckie" The less the Power the More the Force |
|
smfulle
Member Sponsor Member Joined: 16 Sep. 2010 Location: Ogden, Utah Status: Offline Points: 6141 |
Post Options
Thanks(0)
|
A couple from a few years back.
|
|
Post Reply | Page <1 23456 9> |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |