|
|
|
THE parts paint color list |
Post Reply 
|
Page 12> |
| Author | |
m38mike 
Member 
Joined: 23 Apr. 2007 Location: Colorado High Country Status: Offline Points: 3683 |
 Post Options
 Thanks(5)
 Quote Reply
 Topic: THE parts paint color listPosted: 17 Sep. 2007 at 9:30pm |
|
CJ2A - PARTS COLORS: Air cleaner body: gloss black Air cleaner mounts: gloss black Air crossover tube: gloss black Axles: semi-gloss black Axle bumper, frame mounted: semi-gloss black Bell housing: semi-gloss black Bell housing clutch inspection plate: semi-gloss black Brake backing plates: semi-gloss black Brake cylinders: unpainted Brake eccentrics/adjusting nuts: plated or semi-gloss black Brake lines: bare steel Brake line clips and clamps: silver (plated) Brake rubber line crimp ends: plated Brake line T-blocks: brass Brake linkage arms: plated or semi-gloss black Brake pedal: early – OD nonskid; late - gloss black Bumper: gloss black Clutch bellcrank ball studs: plated Clutch pedal: early – OD nonskid; late - gloss black Clutch linkage arms: plated or semi-gloss black Crossmember to frame: semi-gloss black Crossmember bolts: zinc or zinc-color cad plate Dash light: gloss black Distributor body: gloss black Door sockets: gloss black Drive shafts: semi-gloss black E-brake drum: early – OD; late - semi-gloss black E-brake handle: early – gloss black; late – chromed E-brake rachet tube (under dash): gloss black Engine block: semi-gloss black, factory rebuilt: red Engine block rear plate: black Fender & grille fastening bolts & flat washers: cad plate Fender & grille fastening lock washers: blackened or plain blue spring steel Footman loops (includes grill): gloss black Foot rest: gloss black Frame: semi-gloss black Front marker light housing: black Front marker light bezels: early - black, late -chrome Fuel level sending unit: body color (top), plated (in tank) Fuel pump: Yellow chromated pot metal with or without glass bowl Gas can carrier: body color or gloss black Gas cap: body color or gloss black Gas pedal: gloss black Gas tank: body color, replacement tank: gloss black Gas tank ground clip rear: gloss black Gas tank strap: gloss black Gauge trim ring: gloss black Generator: gloss black Generator splash shield: semi-gloss black Hub & studs: semi-gloss black Headlight buckets: early - black; late – chocolate brown Headlight outer rings: early to 38687-body color; late-chrome Headlight retainer rings: early – either black or chrome, late – chrome Heater, black or grey Heater inlet tube, drivers side: early – OD, late - black Hinge, tailgate: body color Hole cover, left rear: body color Hood blocks, oak: gloss black Hood latch: gloss black Horn and bracket: gloss black Knuckle seal half-moons: cad plate - possibly painted black after axle assembly Master cylinder cover: gloss black, bolts zinc or zinc-color cad plate Master cylinder heat shield: semi-gloss black Mirror, outside, pivot, arm & mirror head: gloss black Mirror, outside, body bracket: black or body color Mirror, inside: gloss black Muffler: early – passenger side, OD; late – rear, galvanized NACO tail light body: early to 45723, gloss black with black bezel NACO tail light body: late, gloss black with chrome bezel Oil filler pipe: gloss black Oil filler cap: plated (silver) Oil filter, Fram, early: body and cap gloss black, bolts (silver), with decals Oil filter, Fram, late: body orange, cap gloss black, bolts plated (silver), with decals Oil filter, Purolater: body and cap gloss black, with decals Oil pan: semi-gloss black Oil pump: black Passenger seat hinge blocks: gloss black PTO gear box, rear: Semi-gloss black PTO shaft: semi-gloss black PTO shifter: semi-gloss black or bright unpainted metal Radiator cap: plated (silver) Radiator & shroud: semi-gloss black Rear drawbar tow frame: gloss black Rear seat leg catch (under body): plated (silver) Reflector, rear: early to 67921-gloss black; late-chrome Seat frames: gloss black Shackle seal covers: semi-gloss black. Shift boot rings: gloss black, bolts silver Shock absorbers: gloss black Shock absorber retainer washers: cad plate Skid plate: semi-gloss black Spare tire carrier: gloss black Spring shackles: semi-gloss black Starter: gloss black Steering column & box: gloss black, bolts silver Steering column dash brace: gloss black, bolts silver Steering linkage: semi-gloss black Steering wheel: gloss black Tailgate chain: bright plated (silver) Tailgate “4 Wheel Drive” decal: white or black, accent to body color Thermostat housing: black Timing cover plate: semi-gloss black Top bows and rods: black
Transmission cover, column shift: body color or gloss black Transmission cover, floor shift: gloss black, bolts silver Water pump: black Wheel lug nuts: zinc or cadmium plate (silver); or gloss black Wheels: accent color to body color, with 1/8 to 1/4 inch pinstripe Willys raised lettering: early-body color to 6/47, accent color from 6/47 on Windshield adjust arm, early MB style: cad plate Windshield adjust arm, early MB style knurled nut: cad plate Windshield clips top bow storage: body color Windshield inner frame: body color Windshield outer frame: body color Windshield "popsicles": zinc or zinc-color plate Windshield "popsicle" spring star washers: body color Windshield “popsicle” wing bolts: zinc Windshield hold-down clamps & bolts: zinc or cad plate Windshield hold-down clips on cowl: early-body color or late-gloss black (bolts zinc or cad plate) Windshield pivot bolt: wing - body color; shoulder – zinc Windshield studs for top: gloss black or chrome Windshield wiper manual arm: gloss black Windshield wiper motor: semi-gloss black Windshield wiper arm: gloss black or chrome Windshield wiper vacuum tube: black Edited by samcj2a - 27 Sep. 2013 at 3:12pm |
|
|
M38Mike
46 CJ2A SAMCJ2A 4?-5? CJ2A/3A/M38 Jigsaw 51 M38 Green Jeanne 52 M38 Blue Mule, 51 M100 Blue Mule Tale 52 XM38EV1 Electro-Willys, 52 M100 Juice Box |
|
 |
|
|
Jus*Jack
Member 
Joined: 15 Mar. 2007 Location: so. Georgia Status: Offline Points: 1841 |
Post Options
Thanks(3)
Quote Reply
Posted: 18 Sep. 2007 at 9:09pm |
|
OK...and here is the list of "Parts By Color", for those wishing to group things together when shooting a color. This arrangement is based on the latest revision that I had from Mike, as of 8-25-07:
GLOSS BLACK Air cleaner body Air cleaner mounts Air crossover tube Brake pedal, late Bumper Clutch pedal, late Dash light Distributor body Door sockets E-brake ratchet tube (under dash) Footman loops (includes grill) Foot rest Gas can carrier: body color or gloss black Gas cap: body color or gloss black Gas pedal Gas tank: replacement tank: gloss black Gas tank ground clip rear Gas tank strap Gauge trim ring Generator Hood blocks, oak Hood latch Horn and bracket Master cylinder cover Mirror, outside, pivot, arm & mirror head Mirror, interior NACO tail light body: early to 45723, gloss black with black bezel NACO tail light body: late (after 45723), gloss black with chrome bezel Oil filler pipe Oil filter, Fram, early: body and cap Oil filter, Fram, late: cap Oil filter, Purolater: body and cap, with decals Passenger seat hinge blocks Rear drawbar tow frame Reflector, rear: early to 67921 ??????????? Seat frames Shift boot rings Shock absorbers Spare tire carrier Starter Steering column Steering column dash brace Steering wheel Transmission cover, column shift: body color or gloss black Transmission cover, floor shift Wheel lug nuts: zinc or cadmium plate (silver); or gloss black Windshield hold-down clips on cowl: early-body color or late-gloss black Windshield studs for top: gloss black or chrome Windshield wiper manual arm: gloss black Windshield wiper arm: gloss black or chrome BLACK, SEMI-GLOSS: Axles Axle bumper, frame mounted Bell housing Bell housing clutch inspection plate Brake backing plates Brake linkage arms: plated or semi-gloss black Brake eccentrics/adjusting nuts: plated or semi-gloss black Clutch linkage arms: plated or semi-gloss black Crossmember to frame Drive shafts E-brake drum: early – OD; late - semi-gloss black E-brake handle: early – gloss black; late - chromed Engine block: semi-gloss black, factory rebuilt: red Frame Generator splash shield Hub & studs Master cylinder heat shield Oil pan PTO gear box, rear PTO shaft PTO shifter: semi-gloss black or bright unpainted metal Radiator & shroud Shackle seal covers Skid plate Spring shackles Steering linkage Windshield wiper motor BLACK (GLOSS vs. SEMI-, UNKNOWN) Engine block rear plate Front marker light housing Front marker light bezels: early - black, late -chrome Headlight buckets: early - black; late – chocolate brown Headlight retainer rings: early – either black or chrome, late - chrome Knuckle seal half-moons: cad plate - possibly painted black after axle assembly Mirror, outside, body bracket: black or body color Oil pump Thermostat housing Top bows and rods Water pump Windshield wiper vacuum tube BODY COLOR: Fuel level sending unit: body color (top), plated (in tank) Gas can carrier: body color or gloss black Gas cap: body color or gloss black Gas tank, original Headlight outer rings: early to 38687-body color; late-chrome Hinge, tailgate: body color Hole cover, left rear: body color Transmission cover, column shift: body color or gloss black Wheels: accent color to body color, with 1/8 to 1/4 inch pinstripe Willys raised lettering: early-body color to 6/47, accent color from 6/47 on Windshield clips top bow storage: body color Windshield inner frame: body color Windshield outer frame: body color Windshield hold-down clips on cowl: early-body color or late-gloss black Windshield "popsicle" spring star washers: body color Windshield pivot bolt: wing - body color UNPAINTED OR PLATED: Brake cylinders: unpainted Brake lines: bare steel Brake line clips and clamps: silver (plated) Brake rubber line crimp ends: plated Brake line T-blocks: brass Clutch bellcrank ball studs: plated Crossmember bolts: zinc or zinc-color cad plate Fender & grille fastening bolts & flat washers: cad plate Fender & grille fastening lock washers: blackened or plain blue spring steel Fuel pump: Yellow chromated pot metal with or without glass bowl Master cylinder, bolts zinc or zinc-color cad plate Oil filler cap: plated (silver) Oil filter, Fram, early: bolts (silver) Oil filter, Fram, late: bolts plated (silver) Radiator cap: plated (silver) Rear seat leg catch (under body): plated (silver) Shift boot rings -bolts silver Shock absorber retainer washers: cad plate Steering column bolts silver Steering column dash brace bolts silver Tailgate chain: bright plated (silver) Timing cover plate: plated Transmission cover, floor shift bolts silver Wheel lug nuts: zinc or cadmium plate (silver); or gloss black Windshield "popsicles": zinc or zinc-color plate Windshield “popsicle” wing bolts: zinc Windshield adjust arm, early MB style: cad plate Windshield adjust arm, early MB style knurled nut: cad plate Windshield hold-down clamps & bolts: zinc or cad plate Windshield hold-down clips on cowl bolts zinc or cad plate Windshield pivot bolt shoulder – zinc CHROME: Headlight retainer rings: early – either black or chrome, late - chrome Reflector, rear: after 67921 (late)--chrome Windshield studs for top: gloss black or chrome OTHER: Brake pedal: early – OD nonskid Clutch pedal: early – OD nonskid; Engine block, factory rebuilt: red Muffler: early – passenger side, OD; late – rear, galvanized Oil filter, Fram, late: body orange |
|
|
Seeya!
<Jack> '48 CJ2A 197207 "Junebug" '48 CJ2A 191237 "Turquoise" |
|
|
|
|
woodwizrh
Member
Joined: 04 July 2008 Location: new York Status: Offline Points: 4 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 July 2008 at 12:38am |
|
Thank for the info, Will be a big help. I have built a lot of Jeeps some with V8 engines(wild ride) but this is my first serious restoration. |
|
|
woodwiz
|
|
|
|
|
Jolly Jeeper
Member
Joined: 18 Feb. 2009 Location: Yorkshire, England, Status: Offline Points: 2 |
Post Options
Thanks(0)
Quote Reply
Posted: 18 Feb. 2009 at 3:16pm |
|
Just thought I'd say thanks; found this list while browsing Jeep sites (I'm more usually on the CJ3B page) but here in England we've started rebuilding a pile of rust that was once a '46 CJ-2A and I wanted to know what color the frame should be. I now have the answer! Yesterday we fitted a new rear crossmember to the frame.
JC
|
|
|
flat fenders forever
JC |
|
|
|
|
leef
Member
Joined: 06 Nov. 2005 Location: Vancouver, Wa Status: Offline Points: 66 |
Post Options
Thanks(0)
Quote Reply
Posted: 19 Feb. 2009 at 5:21am |
|
Can anyone recommend an adequate 'rattle can' primer, gloss black and semi-gloss black that would work well for some of the many small parts that require those colors?
|
|
|
leef
462a |
|
|
|
|
m38mike
Member
Joined: 23 Apr. 2007 Location: Colorado High Country Status: Offline Points: 3683 |
Post Options
Thanks(1)
Quote Reply
Posted: 23 Feb. 2009 at 1:12am |
|
leef, I've had good success with Rustoleum brand paints, both rattle can and in quarts.
|
|
|
M38Mike
46 CJ2A SAMCJ2A 4?-5? CJ2A/3A/M38 Jigsaw 51 M38 Green Jeanne 52 M38 Blue Mule, 51 M100 Blue Mule Tale 52 XM38EV1 Electro-Willys, 52 M100 Juice Box |
|
|
|
|
Al Martin
Member
Joined: 11 Feb. 2009 Location: Central Michigan Status: Offline Points: 57 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 Feb. 2009 at 3:13pm |
|
Also try Eastwood. Good stuff.
Al
|
|
|
|
|
trdabney
Member
Joined: 19 Sep. 2005 Location: Jackson, TN Status: Offline Points: 28 |
Post Options
Thanks(0)
Quote Reply
Posted: 10 Mar. 2011 at 3:47am |
|
Before I get ready to reinstall my engine, I would like to repaint it in the factory rebuilt red. Does anyone know of a rattle-can color that will match?
 |
|
|
|
|
losttribe
Member
Joined: 21 May 2011 Location: Utah Status: Offline Points: 8 |
Post Options
Thanks(0)
Quote Reply
Posted: 08 Jan. 2012 at 10:33pm |
|
This list can be very helpful for a fussy restorer. Where did you get this? Is it from Willys literature?
|
|
|
|
|
m38mike
Member
Joined: 23 Apr. 2007 Location: Colorado High Country Status: Offline Points: 3683 |
Post Options
Thanks(0)
Quote Reply
Posted: 09 Jan. 2012 at 2:28am |
|
losttribe,
We folks here on the page put this list together over 2 years ago from the best information that we had available. It was a collective effort to record the paint on each part of a Willys.
|
|
|
M38Mike
46 CJ2A SAMCJ2A 4?-5? CJ2A/3A/M38 Jigsaw 51 M38 Green Jeanne 52 M38 Blue Mule, 51 M100 Blue Mule Tale 52 XM38EV1 Electro-Willys, 52 M100 Juice Box |
|
|
|
|
samcj2a
Member
Sponsor Member x 5 Joined: 21 Oct. 2006 Location: Arlington, VA Status: Offline Points: 8539 |
Post Options
Thanks(1)
Quote Reply
Posted: 13 Sep. 2014 at 4:31pm |
|
I beg to differ about the color of the gas cap. Every vintage photo that shows the cap shows that it was originally black. Body color caps were most likely the result of repainting and contemporary observations,
Take a look at these Reference Photos. Every gas cap that is visible is black. |
|
|
|
|
JAB
Member
Joined: 21 Mar. 2019 Location: WI 53153 Status: Offline Points: 151 |
Post Options
Thanks(0)
Quote Reply
Posted: 31 Mar. 2019 at 3:27am |
|
I don't see the transmission or transfer case listed, or the shifter canes, but I assume semi-gloss black? Thanx!
Edited by JAB - 31 Mar. 2019 at 3:29am |
|
|
GR8GPN2U!
|
|
|
|
|
montymech
Member
Joined: 18 Apr. 2012 Location: Dartford. UK Status: Offline Points: 324 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 June 2019 at 6:48pm |
|
M38mike. Thanks. I'm glad I asked; that's a very comprehensive list.
|
|
|
|
|
Mark W.
Member
Sponsor Member Joined: 09 Nov. 2014 Location: Silverton, OR Status: Offline Points: 7532 |
Post Options
Thanks(1)
Quote Reply
Posted: 05 June 2019 at 12:09am |
|
I am very happy with VHT Epoxy in Satin or Gloss Black. No primer required. It also comes labeled as VHT Roll Bar and Chassis paint
|
|
|
Chug A Lug
1948 2A Body Customized 1949 3A W/S 1957 CJ5 Frame Modified Late 50's 134L 9.25"clutch T90A D18 (1.25") D44/30 flanged E-Locker D25 5.38 Since 1962 |
|
|
|
|
F.T.S.
Member
Joined: 27 July 2009 Location: Medford N.J. Status: Offline Points: 365 |
Post Options
Thanks(0)
Quote Reply
Posted: 15 July 2019 at 1:18am |
|
m38mike
Thanks for the chart. Just what I need. F.T.S.
|
|
|
F.T. Stewart
|
|
|
|
|
Joe B.
Member
Joined: 22 July 2011 Location: South Texas Status: Offline Points: 115 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 Aug. 2019 at 3:08am |
|
DUMB QUESTION......………..WHAT DOES THE MEAN NON SKID ON BRAKE AND CLUTCH PEDALS?
THANKS Joe B. |
|
|
'46 CJ2A South Texas
|
|
|
|
|
Ol' Unreliable
Member
Joined: 25 Sep. 2016 Location: CO Springs CO Status: Offline Points: 4215 |
Post Options
Thanks(0)
Quote Reply
Posted: 05 Aug. 2019 at 2:04am |
|
Brake and clutch pedals had a non-skid paint on them: a paint with some kind of gritty stuff in it, for helping keep your feet from sliding off the pedals. Many has been the time when I wished Ol' Unreliable still had that paint there.
 Edited by Ol' Unreliable - 05 Aug. 2019 at 2:06am |
|
|
There's a reason it's called Ol' Unreliable
|
|
|
|
|
Steelyard Blues
Member
Joined: 09 Oct. 2017 Location: Reno, NV Status: Offline Points: 1399 |
Post Options
Thanks(0)
Quote Reply
Posted: 05 Aug. 2019 at 2:17am |
|
Did not know this about the pedals. Makes sense. This might be a good alternative:
I used it on my front floors to keep them from rusting. It has a bit of texture and is holding up well. Maybe a local shop can squirt them when they do someone's truck Micah
|
|
|
1947 CJ2A 106327, Engine J109205, Tub 97077. Luzon Red
https://www.thecj2apage.com/forums/steelyard-blues_topic41024_post397981.html?KW=micah+movie#397981 1965 Johnson Furnace Company M416 #6-1577 |
|
|
|
|
Post Reply
|
Page 12> |
| Tweet |
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options