various parts in central NC |
Post Reply |
Author | |
NC flatfender
Member Joined: 17 Dec. 2020 Location: central NC Status: Offline Points: 9 |
Post Options
Thanks(0)
Posted: 14 Jan. 2021 at 4:11am |
Just getting back to the forum after a 13 year break!
I am finally motivated to get the nicer of my two cj2As back running. I have several spares to trade: -front engine plates ( 2 gear, one chain) -transmission floor cover -transmission cover with shift forks -complete rear end assembly (Dana 41?) -gear drive crank -starter (unknown condition) -various wheels (see below) I also have a 1950? 4-63 truck, which has not been modified at all. Probably worth restoring, but I just don't have time to get all three back running. This truck has a lot of interchangeable parts with the 2As. Things I am looking for: -complete factory air cleaner assembly -factory 16" wheels I have four factory 16" wheels on each vehicle, but I have at least three different styles. One solid disc, three "heavy duty" with the1/8 inch hole (I suspect two of these are M38, but haven't measured them yet) and several 4.5". I would prefer to end up with 4 16x5 truck wheels. -complete governor (I have factory rear pto, but no governor) -factory steering wheel in decent shape -both front seat frames
Edited by NC flatfender - 05 Feb. 2021 at 1:27am |
|
two CJ2As plus a 4-63 truck, all needing attention
|
|
Red 2a
Member Joined: 20 May 2018 Location: York ME 039309 Status: Offline Points: 3 |
Post Options
Thanks(0)
|
Hi,
I have a 2a I have been working on for a couple years and I have been hitting my head against the wall trying to fix a leaking oil pan. The sad thing is I had a spare engine that I took this leaky off of and sent a perfectly fine military pan with the junk engine. So here I am looking for a solid oil pan. I would prefer one with a skid plate but a non leaking pan would do. You wouldn't happen to have a good oil pan? Thanks
|
|
Jeeper 48Cj2a
|
|
NC flatfender
Member Joined: 17 Dec. 2020 Location: central NC Status: Offline Points: 9 |
Post Options
Thanks(0)
|
I do not have any spare oil pans. The head is off of my '46, but I think it is repairable so I don't want to part it out. I hope to get that one running before long
|
|
two CJ2As plus a 4-63 truck, all needing attention
|
|
Markmar0607
Member Joined: 23 Aug. 2017 Location: South Carolina Status: Offline Points: 55 |
Post Options
Thanks(0)
|
Morning my name is Mark,where are you located in Nc?
|
|
Vintage Don
Member Sponsor Member Joined: 10 Sep. 2020 Location: Medina, OH Status: Offline Points: 413 |
Post Options
Thanks(0)
|
I am very interested in your generator, does it have the Tag still on it?
Also, your transmission floor cover - is this for a floor shift or column shift? Maybe interested in a wheel - gotta do some homework first to know what I need... Thanks.
|
|
19Cargo42
Member Joined: 23 Apr. 2018 Location: Western Mass. Status: Offline Points: 570 |
Post Options
Thanks(0)
|
I’m looking for solid rims for my ‘45 CJ2A project and would be interested to learn more about yours, if it’s not spoken for. I’ll send you a PM.
|
|
Vintage Don
Member Sponsor Member Joined: 10 Sep. 2020 Location: Medina, OH Status: Offline Points: 413 |
Post Options
Thanks(0)
|
Haha - that's the one I was talking about above, too! Naturally.
|
|
19Cargo42
Member Joined: 23 Apr. 2018 Location: Western Mass. Status: Offline Points: 570 |
Post Options
Thanks(0)
|
No problem. Hopefully things will work out for you.
On my list of parts, solid rims are under "nice to have in the future, but not essential now." Interestingly, I think my Jeep came from the factory with the optional slotted 15" rims. Those will go into storage and I'm planning on restoring a set of the 16" slotted ones I've been collecting and using those until I source a set of solids.
Sincerely, John |
|
Vintage Don
Member Sponsor Member Joined: 10 Sep. 2020 Location: Medina, OH Status: Offline Points: 413 |
Post Options
Thanks(0)
|
Roger that - and I've got THREE solid ones - and trying to be certain that they are "correct" for a 46 VEC before I go nuts chasing down a 4th, only to learn later that they're not right, anyway....
|
|
NC flatfender
Member Joined: 17 Dec. 2020 Location: central NC Status: Offline Points: 9 |
Post Options
Thanks(0)
|
Thanks to John for correctly identifying my "solid" wheel as being from a slat grill. I found a guy on the g503 site that traded me two m38 wheels for it. I think we are both happy with that.
Now I just need to find some time and motivation to get the '48 back running. |
|
two CJ2As plus a 4-63 truck, all needing attention
|
|
19Cargo42
Member Joined: 23 Apr. 2018 Location: Western Mass. Status: Offline Points: 570 |
Post Options
Thanks(0)
|
Glad that worked out for you.
John
|
|
Post Reply | |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |