Forum Home Forum Home > CJ-2A Discussion Area > General Discussion
  New Posts New Posts RSS Feed - Where to purchase timing oiler .40
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Where to purchase timing oiler .40

 Post Reply Post Reply
Author
Message
JPR66 View Drop Down
Member
Member
Avatar

Joined: 19 May 2018
Location: Murray, NE
Status: Offline
Points: 6
Post Options Post Options   Thanks (0) Thanks(0)   Quote JPR66 Quote  Post ReplyReply Direct Link To This Post Topic: Where to purchase timing oiler .40
    Posted: 14 May 2019 at 7:38am
I apologize if repeat post. I've looked for suggestions on where to purchase a timing oiler jet. Anyone know where to buy? 

Thanks,
Jon
Jon - CJ2A 47
Back to Top
smfulle View Drop Down
Member
Member
Avatar
Sponsor Member

Joined: 16 Sep. 2010
Location: Ogden, Utah
Status: Offline
Points: 4650
Post Options Post Options   Thanks (0) Thanks(0)   Quote smfulle Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2019 at 9:44am
Call the usual senders. I got one from Walks, but it's not a thing they can order, they just have to have one in their used stuff pile.

Walcks
Ron Fitzpatrick
Kaiser Willys
Stan
48 CJ2A (Grampa's Jeep)
59 Chevy 1/2 ton
Grampa's Jeep Build Thread
Back to Top
Mark W. View Drop Down
Member
Member
Avatar

Joined: 09 Nov. 2014
Location: Silverton, OR
Status: Offline
Points: 4664
Post Options Post Options   Thanks (0) Thanks(0)   Quote Mark W. Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2019 at 4:51pm
Do you have the original .070" if so with a little work you can make it into a .040"

Easiest is to braze up the hole and redrill it with a #60 drill bit.

I went a different route I drilled the hole out to a #29 and threaded it to 8-32 I then took a brass 8-32 screw and threaded it into the hole with RED Loctite and ground the head off flat leaving just the meat below the slot. I then drilled this with a #60 drill bit.


Chug A Lug
1948 2A Body Customized
1949 3A W/S
1957 CJ5 Frame Modified
Late 50's 134L 9.25"clutch T90A D18 (1.25") D44/30 flanged E-Locker D25 5.38 Since 1962
Back to Top
JPR66 View Drop Down
Member
Member
Avatar

Joined: 19 May 2018
Location: Murray, NE
Status: Offline
Points: 6
Post Options Post Options   Thanks (0) Thanks(0)   Quote JPR66 Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2019 at 5:08pm
I have a message to Walcks to see if they have any, thanks for the advice.
Jon - CJ2A 47
Back to Top
JPR66 View Drop Down
Member
Member
Avatar

Joined: 19 May 2018
Location: Murray, NE
Status: Offline
Points: 6
Post Options Post Options   Thanks (0) Thanks(0)   Quote JPR66 Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2019 at 5:12pm
Unfortunately, I don't have any others. I inherited the Jeep after partial restoration and trying to finish it up. The motor was rebuilt about 15 years ago and they forgot to put in a timing oiler in the rebuild. Thank you for your response and instructions.
Jon - CJ2A 47
Back to Top
Bruce W View Drop Down
Member
Member
Avatar

Joined: 29 July 2005
Location: Northeast Colorado
Status: Offline
Points: 5713
Post Options Post Options   Thanks (0) Thanks(0)   Quote Bruce W Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2019 at 8:08pm
  If you can't find an .040 and would like to have an .070 to plug and re-drill, I believe I have a spare I could let you have cheap. BW
Happy Trails! Good-bye, Good Luck, and May the Good Lord Take a Likin' to You!

We Have Miles to Jeep, Before We Sleep.
Back to Top
JPR66 View Drop Down
Member
Member
Avatar

Joined: 19 May 2018
Location: Murray, NE
Status: Offline
Points: 6
Post Options Post Options   Thanks (0) Thanks(0)   Quote JPR66 Quote  Post ReplyReply Direct Link To This Post Posted: 15 May 2019 at 7:24am
Thanks Bruce! I'll let you know how the hunt goes. I did find both .70 and .40 listed at https://www.willysjeepparts.com/, have never bought from them. Going to call and see if they have it in stock.
Jon - CJ2A 47
Back to Top
athawk11 View Drop Down
Member
Member
Avatar

Joined: 17 Jan. 2012
Location: Arvada,Colorado
Status: Offline
Points: 3322
Post Options Post Options   Thanks (0) Thanks(0)   Quote athawk11 Quote  Post ReplyReply Direct Link To This Post Posted: 15 May 2019 at 10:53pm
I have purchased from this vendor in the past.  The process is a bit archaic compared to the way we purchase things these days, but the transaction went fine and the stuff I bought was nice.
1- 1946 CJ2A   
2- 1949 CJ3A
Back to Top
JPR66 View Drop Down
Member
Member
Avatar

Joined: 19 May 2018
Location: Murray, NE
Status: Offline
Points: 6
Post Options Post Options   Thanks (0) Thanks(0)   Quote JPR66 Quote  Post ReplyReply Direct Link To This Post Posted: 16 May 2019 at 6:27am
Thank you for the reply and feedback!
Jon - CJ2A 47
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.01
Copyright ©2001-2018 Web Wiz Ltd.